173 lines
5.2 KiB
C
173 lines
5.2 KiB
C
/**
|
|
******************************************************************************
|
|
* @file Examples_LL/GPIO/GPIO_InfiniteLedToggling/Src/main.c
|
|
* @author MCD Application Team
|
|
* @brief This example describes how to configure and use GPIOs through
|
|
* the STM32F1xx GPIO LL API.
|
|
* Peripheral initialization done using LL unitary services functions.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "main.h"
|
|
|
|
/** @addtogroup STM32F1xx_LL_Examples
|
|
* @{
|
|
*/
|
|
|
|
/** @addtogroup GPIO_InfiniteLedToggling
|
|
* @{
|
|
*/
|
|
|
|
/* Private typedef -----------------------------------------------------------*/
|
|
/* Private define ------------------------------------------------------------*/
|
|
/* Private macro -------------------------------------------------------------*/
|
|
/* Private variables ---------------------------------------------------------*/
|
|
/* Private function prototypes -----------------------------------------------*/
|
|
void SystemClock_Config(void);
|
|
void Configure_GPIO(void);
|
|
|
|
|
|
/* Private functions ---------------------------------------------------------*/
|
|
|
|
/**
|
|
* @brief Main program
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
int main(void)
|
|
{
|
|
/* Configure the system clock to 72 MHz */
|
|
SystemClock_Config();
|
|
|
|
/* -2- Configure IO in output push-pull mode to drive external LED */
|
|
Configure_GPIO();
|
|
|
|
/* Toggle IO in an infinite loop */
|
|
while (1)
|
|
{
|
|
LL_GPIO_TogglePin(LED2_GPIO_PORT, LED2_PIN);
|
|
|
|
/* Insert delay 250 ms */
|
|
LL_mDelay(250);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief This function configures GPIO
|
|
* @note Peripheral configuration is minimal configuration from reset values.
|
|
* Thus, some useless LL unitary functions calls below are provided as
|
|
* commented examples - setting is default configuration from reset.
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
void Configure_GPIO(void)
|
|
{
|
|
/* Enable the LED2 Clock */
|
|
LED2_GPIO_CLK_ENABLE();
|
|
|
|
/* Configure IO in output push-pull mode to drive external LED2 */
|
|
LL_GPIO_SetPinMode(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_MODE_OUTPUT);
|
|
/* Reset value is LL_GPIO_OUTPUT_PUSHPULL */
|
|
//LL_GPIO_SetPinOutputType(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_OUTPUT_PUSHPULL);
|
|
/* Reset value is LL_GPIO_SPEED_FREQ_LOW */
|
|
//LL_GPIO_SetPinSpeed(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_SPEED_FREQ_LOW);
|
|
/* Reset value is LL_GPIO_PULL_NO */
|
|
//LL_GPIO_SetPinPull(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_PULL_NO);
|
|
}
|
|
|
|
/**
|
|
* @brief System Clock Configuration
|
|
* The system Clock is configured as follow :
|
|
* System Clock source = PLL (HSE)
|
|
* SYSCLK(Hz) = 72000000
|
|
* HCLK(Hz) = 72000000
|
|
* AHB Prescaler = 1
|
|
* APB1 Prescaler = 2
|
|
* APB2 Prescaler = 1
|
|
* HSE Frequency(Hz) = 8000000
|
|
* PLLMUL = 9
|
|
* Flash Latency(WS) = 2
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
void SystemClock_Config(void)
|
|
{
|
|
/* Set FLASH latency */
|
|
LL_FLASH_SetLatency(LL_FLASH_LATENCY_2);
|
|
|
|
/* Enable HSE oscillator */
|
|
LL_RCC_HSE_EnableBypass();
|
|
LL_RCC_HSE_Enable();
|
|
while(LL_RCC_HSE_IsReady() != 1)
|
|
{
|
|
};
|
|
|
|
/* Main PLL configuration and activation */
|
|
LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSE_DIV_1, LL_RCC_PLL_MUL_9);
|
|
|
|
LL_RCC_PLL_Enable();
|
|
while(LL_RCC_PLL_IsReady() != 1)
|
|
{
|
|
};
|
|
|
|
/* Sysclk activation on the main PLL */
|
|
LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1);
|
|
LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);
|
|
while(LL_RCC_GetSysClkSource() != LL_RCC_SYS_CLKSOURCE_STATUS_PLL)
|
|
{
|
|
};
|
|
|
|
/* Set APB1 & APB2 prescaler*/
|
|
LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_2);
|
|
LL_RCC_SetAPB2Prescaler(LL_RCC_APB2_DIV_1);
|
|
|
|
/* Set systick to 1ms in using frequency set to 72MHz */
|
|
LL_Init1msTick(72000000);
|
|
|
|
/* Update CMSIS variable (which can be updated also through SystemCoreClockUpdate function) */
|
|
LL_SetSystemCoreClock(72000000);
|
|
}
|
|
|
|
#ifdef USE_FULL_ASSERT
|
|
|
|
/**
|
|
* @brief Reports the name of the source file and the source line number
|
|
* where the assert_param error has occurred.
|
|
* @param file: pointer to the source file name
|
|
* @param line: assert_param error line source number
|
|
* @retval None
|
|
*/
|
|
void assert_failed(uint8_t *file, uint32_t line)
|
|
{
|
|
/* User can add his own implementation to report the file name and line number,
|
|
ex: printf("Wrong parameters value: file %s on line %d", file, line) */
|
|
|
|
/* Infinite loop */
|
|
while (1)
|
|
{
|
|
}
|
|
}
|
|
#endif
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|