69 lines
2.9 KiB
Plaintext
69 lines
2.9 KiB
Plaintext
/**
|
|
@page RCC_UseHSI_PLLasSystemClock RCC example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file Examples_LL/RCC/RCC_UseHSI_PLLasSystemClock/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the RCC_UseHSI_PLLasSystemClock example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Modification of the PLL parameters in run time.
|
|
|
|
In this example, the toggling frequency of the green LED2 depends on the system clock
|
|
frequency and, each time the user-button is pressed, the PLL switches between two configurations.
|
|
This make the LED2 blinking speed to highlight the system clock frequency changes.
|
|
|
|
In this example, after start-up, SYSCLK is configured to the max frequency using the PLL with
|
|
HSE as clock source.
|
|
Then, at user-button press, an automatic switch is done between PLL with HSI as clock source (SYSCLK
|
|
set to 32MHz) and PLL with HSI as clock source (SYSCLK set to 64MHz).
|
|
LED2 will toggle differently between the 2 configurations (quick toggle with HSI configuration at 64MHz).
|
|
|
|
To detect a problem with PLL configuration, switch USE_TIMEOUT can be enabled. Then in case of issues,
|
|
LED2 will toggle every 1 second.
|
|
Note: "uwFrequency" variable can be added in LiveWatch to monitor the system clock frequency.
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Inc/main.h Header for main.c module
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Src/stm32f1xx_it.c Interrupt handlers
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Src/main.c Main program
|
|
- RCC/RCC_UseHSI_PLLasSystemClock/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xB devices.
|
|
|
|
- This example has been tested with STM32F103RB-Nucleo board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|