70 lines
2.6 KiB
Plaintext
70 lines
2.6 KiB
Plaintext
/**
|
|
@page PWR_EnterStopMode PWR stop example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file Examples_LL/PWR/PWR_EnterStopMode/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWR STOP_MAINREGU mode example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to enter the STOP_MAINREGU mode.
|
|
|
|
After start-up LED2 is toggling during 5 seconds, then the system automatically
|
|
enter in STOP_MAINREGU mode (Final state).
|
|
|
|
LED2 is used to monitor the system state as follows:
|
|
- LED2 toggling : system in RUN mode
|
|
- LED2 off : system in STOP_MAINREGU mode
|
|
|
|
@note To measure the current consumption in STOP_MAINREGU mode, remove JP6 jumper
|
|
and connect an ampere meter to JP6 to measure IDD current.
|
|
|
|
@note This example can not be used in DEBUG mode due to the fact
|
|
that the Cortex-M3 core is no longer clocked during low power mode
|
|
so debugging features are disabled.
|
|
|
|
@par Directory contents
|
|
|
|
- PWR/PWR_EnterStopMode/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- PWR/PWR_EnterStopMode/Inc/main.h Header for main.c module
|
|
- PWR/PWR_EnterStopMode/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- PWR/PWR_EnterStopMode/Src/stm32f1xx_it.c Interrupt handlers
|
|
- PWR/PWR_EnterStopMode/Src/main.c Main program
|
|
- PWR/PWR_EnterStopMode/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xB devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32F103RB-Nucleo
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32F103RB-Nucleo Set-up
|
|
- LED2 connected to PA.05 pin
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|