86 lines
3.9 KiB
Plaintext
86 lines
3.9 KiB
Plaintext
/**
|
|
@page FLASH_EraseProgram FLASH Erase and Program example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file FLASH/FLASH_EraseProgram/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the FLASH Erase and Program example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to configure and use the FLASH HAL API to erase and program the internal
|
|
Flash memory.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system clock (SYSCLK)
|
|
to run at 64 MHz.
|
|
|
|
After Reset, the Flash memory Program/Erase Controller is locked. A dedicated function
|
|
is used to enable the FLASH control register access.
|
|
Before programming the desired addresses, an erase operation is performed using
|
|
the flash erase page feature. The erase procedure is done by filling the erase init
|
|
structure giving the starting erase page and the number of pages to erase.
|
|
At this stage, all these pages will be erased one by one separately.
|
|
|
|
@note: if problem occurs on a page, erase will be stopped and faulty page will
|
|
be returned to user (through variable 'pageError').
|
|
|
|
Once this operation is finished, page word programming operation will be performed
|
|
in the Flash memory. The written data is then read back and checked.
|
|
|
|
The STM32F103RB-Nucleo board LEDs can be used to monitor the transfer status:
|
|
- LED2 is ON when there are no errors detected after programmation
|
|
- LED2 is blinking with a 1s period when there are errors dectected after programmation
|
|
- LED2 is blinking (100ms on, 2s off) when there is an issue during erase or program procedure
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- FLASH/FLASH_EraseProgram/Inc/stm32f1xx_hal_conf.h HAL Configuration file
|
|
- FLASH/FLASH_EraseProgram/Inc/stm32f1xx_it.h Header for stm32f1xx_it.c
|
|
- FLASH/FLASH_EraseProgram/Inc/main.h Header for main.c module
|
|
- FLASH/FLASH_EraseProgram/Src/stm32f1xx_it.c Interrupt handlers
|
|
- FLASH/FLASH_EraseProgram/Src/main.c Main program
|
|
- FLASH/FLASH_EraseProgram/Src/system_stm32f1xx.c STM32F1xx system clock configuration file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xB devices.
|
|
|
|
- This example has been tested with STM32F103RB-Nucleo board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following:
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|