135 lines
6.2 KiB
Plaintext
135 lines
6.2 KiB
Plaintext
/**
|
|
@page UART_TwoBoards_ComPolling UART TwoBoards Communication Polling example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file UART/UART_TwoBoards_ComPolling/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the UART Two Boards Communication Polling example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
UART transmission (transmit/receive) in Polling mode
|
|
between two boards.
|
|
|
|
Board: STM3210C-EVAL RevC (embeds a STM32F107xC device)
|
|
Tx Pin: PD.05
|
|
Rx Pin: PD.06
|
|
_________________________ _________________________
|
|
| ______________| |______________ |
|
|
| |USART | | USART| |
|
|
| | | | | |
|
|
| | TX |_____________________| RX | |
|
|
| | | | | |
|
|
| | | | | |
|
|
| | | | | |
|
|
| | RX |_____________________| TX | |
|
|
| | | | | |
|
|
| |______________| |______________| |
|
|
| | | |
|
|
| | | |
|
|
|_STM32_Board 1___________| |_STM32_Board 2___________|
|
|
|
|
|
|
|
|
Two identical boards are connected as shown on the picture above.
|
|
Board 1: transmitting then receiving board
|
|
Board 2: receiving then transmitting board
|
|
The user presses the Key push-button on board 1.
|
|
Then, board 1 sends in polling mode a message to board 2 that sends it back to
|
|
board 1 in polling mode as well.
|
|
Finally, board 1 and 2 compare the received message to that sent.
|
|
If the messages are the same, the test passes.
|
|
|
|
|
|
WARNING: as both boards do not behave the same way, "TRANSMITTER_BOARD" compilation
|
|
switch is defined in /Src/main.c and must be enabled
|
|
at compilation time before loading the executable in the board that first transmits
|
|
then receives.
|
|
The receiving then transmitting board needs to be loaded with an executable
|
|
software obtained with TRANSMITTER_BOARD disabled.
|
|
|
|
STM3210C-EVAL RevC board LEDs are used to monitor the transfer status:
|
|
- While board 1 is waiting for the user to press the Key push-button, its LED1 is
|
|
blinking rapidly (100 ms period).
|
|
- When the test passes, LED3 and LED4 on both boards are both turned on:
|
|
* LED4 is ON when the transmission process is complete.
|
|
* LED3 is ON when the reception process is complete.
|
|
If LED3 and LED4 are not both turned on, the test has failed.
|
|
- If there is an initialization or transfer error, LED1 is turned on.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 72 MHz.
|
|
|
|
|
|
The UART is configured as follows:
|
|
- BaudRate = 9600 baud
|
|
- Word Length = 8 bits (8 data bits, no parity bit)
|
|
- One Stop Bit
|
|
- No parity
|
|
- Hardware flow control disabled (RTS and CTS signals)
|
|
- Reception and transmission are enabled in the time
|
|
|
|
@note USARTx/UARTx instance used and associated resources can be updated in "main.h"
|
|
file depending hardware configuration used.
|
|
|
|
@note When the parity is enabled, the computed parity is inserted at the MSB
|
|
position of the transmitted data.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- UART/UART_TwoBoards_ComPolling/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- UART/UART_TwoBoards_ComPolling/Inc/stm32f1xx_it.h interrupt handlers header file
|
|
- UART/UART_TwoBoards_ComPolling/Inc/main.h Header for main.c module
|
|
- UART/UART_TwoBoards_ComPolling/Src/stm32f1xx_it.c interrupt handlers
|
|
- UART/UART_TwoBoards_ComPolling/Src/main.c Main program
|
|
- UART/UART_TwoBoards_ComPolling/Src/stm32f1xx_hal_msp.c HAL MSP module
|
|
- UART/UART_TwoBoards_ComPolling/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F107xC devices.
|
|
- This example has been tested with two STM3210C-EVAL RevC boards embedding
|
|
a STM32F107xC device and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM3210C-EVAL RevC set-up
|
|
- Connect a wire between 1st board PD.05 pin (Uart Tx) and 2nd board PD.06 pin (Uart Rx)
|
|
- Connect a wire between 1st board PD.06 pin (Uart Rx) and 2nd board PD.05 pin (Uart Tx)
|
|
- Connect 1st board GND to 2nd Board GND
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|