96 lines
3.7 KiB
Plaintext
96 lines
3.7 KiB
Plaintext
/**
|
|
@page HAL_TimeBase_TIM HAL Time base example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file HAL/HAL_TimeBase/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the HAL time base example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to customize HAL using a general-purpose timer as main source of time base
|
|
instead of Systick.
|
|
|
|
In this example the used timer is TIM2.
|
|
|
|
Time base duration is kept unchanged: 1ms since PPP_TIMEOUT_VALUEs are defined
|
|
and handled in milliseconds basis.
|
|
|
|
The example brings, in user file, a new implementation of the following HAL weak functions:
|
|
|
|
HAL_InitTick()
|
|
HAL_SuspendTick()
|
|
HAL_ResumeTick()
|
|
|
|
This implementation will overwrite native implementation in stm32f1xx_hal.c
|
|
and so user functions will be invoked instead when called.
|
|
|
|
The following time base functions are kept as implemented natively:
|
|
|
|
HAL_IncTick()
|
|
HAL_Delay()
|
|
|
|
When user pushes the User push-button, the Tick increment is suspended if it is already
|
|
enabled, else it will be resumed.
|
|
In an infinite loop, LED3 toggles spaced out over 1s delay.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in TIM2 ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the TIM2 interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the TIM2 interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the TIM2 time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
System, General purpose Timer, Time base, HAL
|
|
|
|
@par Directory contents
|
|
|
|
- HAL/HAL_TimeBase_TIM/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- HAL/HAL_TimeBase_TIM/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- HAL/HAL_TimeBase_TIM/Inc/stm32f1xx.h Header for main.c module
|
|
- HAL/HAL_TimeBase_TIM/Src/stm32f1xx_it.c Interrupt handlers
|
|
- HAL/HAL_TimeBase_TIM/Src/main.c Main program
|
|
- HAL/HAL_TimeBase_TIM/Src/stm32f1xx_hal_timebase_tim.c HAL time base functions
|
|
- HAL/HAL_TimeBase_TIM/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F1xx devices.
|
|
- In this example, the clock is set to 24 MHz.
|
|
|
|
- This example has been tested with STMicroelectronics STM32VL-Discovery
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32VL-Discovery Set-up
|
|
- Use LED3 connected to PC.09 pin and connect them on an oscilloscope
|
|
to show the Time Base signal.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|