68 lines
2.7 KiB
Plaintext
68 lines
2.7 KiB
Plaintext
/**
|
|
@page RCC_UseHSEasSystemClock RCC Clock Config example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file Examples_LL/RCC/RCC_UseHSEasSystemClock/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the RCC HSE start example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Use of the RCC LL API to start the HSE and use it as system clock.
|
|
|
|
At start-up, HSI clock is used as system clock (default clock after reset) and then Systick is
|
|
configured at 1 ms using HSI_VALUE define.
|
|
|
|
Then, HSE is started and we wait for ready state. System clock is set to HSE thanks to IT
|
|
triggered by HSE ready.
|
|
- LED2 is turned ON to indicate that HSE is ready.
|
|
- LED2 is toggled with a timing of 1 second in case of error to switch SYSCLK to HSE or if HSE CSS
|
|
failure is detected (through NMI IT).
|
|
|
|
@note In HSE bypass mode, input clock will come from the MCO from
|
|
ST_LINK MCU. This frequency cannot be changed, and it is fixed
|
|
at 8 MHz. To use MCO from ST_LINK you need to check the Board
|
|
User Manual to know how to connect the MCO pin to the STM32 device.
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- RCC/RCC_UseHSEasSystemClock/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- RCC/RCC_UseHSEasSystemClock/Inc/main.h Header for main.c module
|
|
- RCC/RCC_UseHSEasSystemClock/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- RCC/RCC_UseHSEasSystemClock/Src/stm32f1xx_it.c Interrupt handlers
|
|
- RCC/RCC_UseHSEasSystemClock/Src/main.c Main program
|
|
- RCC/RCC_UseHSEasSystemClock/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xB devices.
|
|
|
|
- This example has been tested with STM32F103RB-Nucleo
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|