106 lines
4.8 KiB
Plaintext
106 lines
4.8 KiB
Plaintext
/**
|
|
@page I2S_AUDIO How to use the Audio features with I2S peripheral
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file I2S/I2S_Audio/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the I2S Audio Example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Basic implementation of audio features. This example allows playing an audio
|
|
file with an external codec on the STM32F1xx board through the I2S
|
|
peripheral using DMA transfer.
|
|
|
|
In this example the I2S input clock, provided by a dedicated PLL (PLLI2S), is
|
|
configured to have an audio sampling frequency at 8 KHz with Master clock enabled.
|
|
|
|
This example uses an audio codec driver which consists of two independent layers:
|
|
- Codec Hardware layer: which controls and communicates with the audio codec
|
|
(CS43L22) implemented on the evaluation board.
|
|
- The high layer: which implements overall control and interfacing API allowing
|
|
to perform basic audio operations (Init, Play, Pause, Resume, Stop, Volume
|
|
control and audio file pointer management)
|
|
|
|
In this example the audio file is stored in the internal flash memory (Mono,
|
|
16-bit, 8 KHz). The analog output device is automatically detected (Speaker or
|
|
Headphone) when the Headphone is plugged/unplugged in/from the audio jack of the
|
|
evaluation board. The example also manages information display and control interface
|
|
through push buttons:
|
|
- When the application is Playing audio file:
|
|
+ KEY push button: Pause
|
|
+ WAKEUP push button: Volume UP
|
|
+ TAMPER: Volume DOWN
|
|
- When the application is Paused:
|
|
+ KEY push button: Play
|
|
+ WAKEUP push button: Switch output target to Headphone
|
|
+ TAMPER: Switch output target to Speaker
|
|
This example plays the audio file stored in internal flash memory and replays it
|
|
when it reaches end of file. But it can be tailored to used different media storage
|
|
devices (SDCard (through SDIO), external Memory (through FSMC) ...) or to play
|
|
in streaming mode (ie. from USB port in device or host mode). In this case, Circular
|
|
DMA mode should be preferred (by enabling the define DMA_CIRCULAR in
|
|
I2Sx_MspInit() API of stm3210c_eval_audio.c file).
|
|
|
|
List of Known Limitations and more detailed user notes are provided in file
|
|
stm3210c_eval_audio.c (under Drivers\BSP\STM3210C-EVAL RevC)
|
|
|
|
The provided sample Audio file (stored in internal Flash memory) is extracted from:
|
|
- Title: Partita E major, Gavotte en rondeau
|
|
- Artist/Composer: J.-S. Bach
|
|
|
|
@par Directory contents
|
|
|
|
- I2S/I2S_Audio/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- I2S/I2S_Audio/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- I2S/I2S_Audio/Inc/main.h Header for main.c module
|
|
- I2S/I2S_Audio/Src/stm32f1xx_it.c Interrupt handlers
|
|
- I2S/I2S_Audio/Src/main.c Main program
|
|
- I2S/I2S_Audio/Src/stm32f1xx_hal_msp.c HAL MSP file
|
|
- I2S/I2S_Audio/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
- I2S/I2S_Audio/Src/audio_sample.c Audio Sample file (in tab format)
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F107xC devices.
|
|
|
|
- This example has been tested with STM3210C-EVAL RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM3210C-EVAL RevC Set-up
|
|
|
|
@par How to use it ?
|
|
|
|
- Use STLink utility, available on www.st.com or any other in system programming
|
|
tool to load a ".wav" file to the STM32 internal flash at the address 0x0800E300.
|
|
Make sure the audio file size does not exceed 512KB. When using STLink utility change
|
|
the audio file extension to "*.bin" in order to be able to load it directly to flash memory.
|
|
@note Audio file present in .\Utilities\Media\AudioFile\ folder
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
@note Make sure that the tool flash loader does not erase or overwrite the
|
|
loaded audio file at address 0x0800E300 by limiting the application
|
|
end address to 0x0803FFFF. This is already done for the example project
|
|
- Connect a headphone or a speaker to the audio jack connector (CN7).
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|
|
|