80 lines
3.4 KiB
Plaintext
80 lines
3.4 KiB
Plaintext
/**
|
|
@page STemWin_HelloWorld Readme file
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file STemWin_HelloWorld/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under Ultimate Liberty license
|
|
* SLA0044, the "License"; You may not use this file except in compliance with
|
|
* the License. You may obtain a copy of the License at:
|
|
* www.st.com/SLA0044
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
|
|
@par Description
|
|
|
|
Simple "Hello World" example based on STemWin.
|
|
|
|
The example allows also to run the different Segger samples that can be
|
|
downloaded from here:
|
|
http://www.segger.com/emwin-samples.html
|
|
To do this, user has only to replace the file "Basic_HelloWorld.c" into the
|
|
project workspace by the downloaded one.
|
|
|
|
Note that the following user files may need to be updated:
|
|
LCDConf_stm3210e_eval.c
|
|
GUIConf_stm3210e_eval.c
|
|
(if for example more GUI allocated memory is needed)
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- STemWin/STemWin_HelloWorld/Inc/GUIConf.h Header for GUIConf_stm3210e_eval.c
|
|
- STemWin/STemWin_HelloWorld/Inc/LCDConf_stm3210e_eval.h Header for LCDConf_stm3210e_eval.c
|
|
- STemWin/STemWin_HelloWorld/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- STemWin/STemWin_HelloWorld/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- STemWin/STemWin_HelloWorld/Inc/main.h Header for main.c module
|
|
- STemWin/STemWin_HelloWorld/Src/stm32f1xx_it.c Interrupt handlers
|
|
- STemWin/STemWin_HelloWorld/Src/BASIC_HelloWorld.c Simple demo drawing "Hello world"
|
|
- STemWin/STemWin_HelloWorld/Src/GUIConf_stm3210e_eval.c Display controller initialization
|
|
- STemWin/STemWin_HelloWorld/Src/LCDConf_stm3210e_eval.c Configuration file for the GUI library
|
|
- STemWin/STemWin_HelloWorld/Src/main.c Main program
|
|
- STemWin/STemWin_HelloWorld/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xG devices.
|
|
|
|
- This example has been tested with STM3210E-EVAL RevD board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|